Which cure time should be used for the Hilti HIT-RE 500 V3?
Two cure times are listed since HIT-RE 500 V3 has relatively long cure times. The initial cure time “t cure ini” is the time at which 25% of the working load could be applied. The full cure time “t cure full” is time at which 100% of the working load could be applied. For installations where the anchor installed is submerged, the hole ...
Submittals for Hilti RE 500 SD
Please note that Hilti HIT-RE 500 V3 has replaced HIT-RE 500 SD which was phased out. On the Submittal Generator, you will be able to select the options for information to include such as the substitution letter for HIT-RE 500 V3 when being used in place of HIT-RE 500SD, product technical information, ICC-ES report, Safety Data Sheets (SDS ...
HIT-RE 500 V3 and ACI 355 - Hilti HIT-RE 500 V3, ACI 355 - Hil...
Hilti's HIT-RE 500 V3 does meet the requirements of ACI 355.4, per Section 6.0 of ESR-3814. Regards, Matthew.
RE-500 Curing time - Hilti USA
Cure times for HIT-RE 500 V3, dependent on the base material temperature, can be found in Figure 9 on page 181 of the Hilti Anchor Fastening Technical Guide. Two cure times are listed since HIT-RE 500 V3 has relatively long cure times. The initial cure time “tcure,ini” is the time at which 25% of the working load could be applied.
HIT-RE 500 cure time - cure time, full strength - seo.title.as... - Hilti
1 Reply. Posted by Matthew Ford3 months ago. Hilti Verified. Hi Nathan, HIT-RE 500 V3 develops full strength after it has fully cured. Cure times based on base material temperature may be found in the Instruction for Use for HIT-RE 500 V3 on Hilti's website. Regards,
Hilti HIT-RE 500 v3 - once frozen
Hilti adhesive anchors have storage and transportation, installation, and in-service temperature requirements. The storage and transportation temperature requirements for HIT-RE 500 V3 are 41 - 77 °F. Unfortunately, Hilti does not have testing for temperatures outside the requirements, and does not recommend using adhesive after being frozen. Hi!
What size hole do I drill/ how much hilti 500 epoxy do I use.
Here is the link to the Hilti Anchor Fastening Technical Guide. The nominal bit diameter for threaded rod with HIT-RE 500 V3 can be found in Table 24 on page 128. Additionally, here is the link for information on the adhesive anchor volume calculator in order to determine the amount of adhesive required for your application. That was a great help.
Oversized Holes with Epoxy (HY-200 or HIT-RE-500) - Anchor, Bo.
Hilti Verified. Jonathan: As noted in our previous response, Hilti has limited test data for oversize holes with our HIT-RE 500 V3 epoxy adhesive. HIT-HY 200 should not be used for oversized hole applications. You may want to consider field testing to determine anchor capacity in conjunction with Engineering judgment to evaluate the suitability ...
Hilti HIT-HY 200-A vs Hilti-RE 500 V4 for Anchors
ANCHORS, Hilti HIT-HY 200-A, Hilti-RE 500 V4, coating,no coating. 0 Likes. 1 Reply. 1 Reply. Posted by Emily almost 2 years ago. Hilti Verified. Hi Bharani, Ask Hilti is a platform designed for customers in Hilti North America. For the best possible assistance, please reach out to your local Hilti Customer Service at 0800 888 5522.
RE 500 fire approval - Chemical Anchoring for Concrete, Hilti ...
1 Reply. Please see this response to a similar question and refer to this exchange for additional information. For further assistance, please contact [email protected]. I was going through RE 500 V3 data sheet, there is no fire approval in the anchor and rebar as anchor section. Where as there is fire approval in the rebar section.