framing screws | Contractor Talk - Professional Construction and ...
2011年1月9日 · Tools & Equipment ...
Hardie to steel frame. Screws or nails? - Contractor Talk
2009年9月29日 · Trim is installed using an ET&F Model 110 tool or 210 tool. These tools and pins are designed specifically for fastening Hardie trim to metal stud framing. They also make a systems for attaching James Hardie siding direct to concrete block and plywood to metal stud framing / steel trusses. The phone number for ET&F Fastening Systems is 800-248 ...
Metal studs attached to ceiling grid - Contractor Talk
2013年2月1日 · I am framing 10' x 10' rooms in a space with the acoustical ceiling already in place. We are using 3 5/8" metal studs and the ceilings are 10' high. The GC said to leave the ceiling and attach the framing to the ceiling. Do I just screw the top track to the ceiling grid with the same screws used for attaching the studs to the track?
#9 3 inch screw or #10 3 inch screws for floor joist
2021年5月28日 · The joist itself is connected to the bottom plate with toe nails. The connection through rim can be achieved with nails or structural screws. GRK R4's will do the job, but nails are faster. I use a fair few screws, though never for sub floor framing as they're expensive.
Drywall & Steel Studs - Impact Driver or Drill?? - Contractor Talk
2020年5月30日 · B) Drywall screws are also not threaded all the way up to the underside of the head of the screw. C) Plus, joining metal to metal the screws don't need to be long - only 1/4" - 1/2". For those reasons, I don't think that drywall screws of either pitch are a good choice for metal stud framing. (I already have a crap-load of #7 x 7/16" self ...
Attaching plywood for roof sheathing? Screws? - Contractor Talk
2007年7月26日 · we use atleast 2 1/4" to 2 1/2" screws to put down 1/2" inch plywood or OSB, but most of the time we use 2 3/8" coated coil nails also known as #8's for hand nailing. Save Share
Removing Painted And Bondo'd Over Deck Screws
2020年10月11日 · In this video I have a newer board that has only screws but a lot of the deck has a mix of nails and screws. Previous owner added screws to try to secure the old wood while leaving nails so a big section is a mix of screws and nails. I did try to just remove the boards with a bull bar but didnt have much luck on boards with the screws.
DensGlass Sheathing Fasteners - Contractor Talk
2010年5月10日 · angus242. 20832 posts · Joined 2007. #4 · May 10, 2010. "Fasteners should be driven flush with the panel surface (not countersunk) and into the framing system. Locate fasteners at least 3/8” (9 mm) from the ends and edges of the sheathing. Nails or screws, as listed in the fastener chart, may be used to attach DensGlass Sheathing to framing.
Framing screws | Page 2 | Contractor Talk - Professional …
2013年3月25日 · What kind of screws are you guys using for interior framing? The company I used to work for always used 3" drywall screws, now that I'm on my own I'm looking for something better.
About ready to give up on prehung doors | Contractor Talk ...
2024年9月16日 · Assuming you're talking about the jamb bowing toward the center of the door, I've always been able to straighten that out with a deck screw or two. Of course that assumes you have good solid framing to run the screws into. You must have a heck of a bow.