How far can you take your service entrance wires into a...
2010年7月28日 · As per local rule we can run service feeders unfused if encased in 3" of cement or buried in conduit under the slab. The restriction is no more than 5' of seu or conduit exposed or concealed unfused out here, some often get a unwritten pass thru a crawlspace ( strapping se cable to bottom of joist) .
SE Cable Sheathing Repair - Electrician Talk
2016年2月17日 · frenchelectrican. 8662 posts · Joined 2007. #5 · Feb 20, 2016. Best to replace it due the water can get into the sheating and water can go down to breakerbox or fuse box and can do some damage from that. It is pretty much SOP to just change it to new one or run new one in conduit ( this what I rather do this in most case ) and be done with it..
3 wire residential panel vs 4 wite - Electrician Talk
2017年10月20日 · I'm a little confused here. I've only seen 3 wire service entrance cables to residential panels. In the main panel I understand the ground and neutral are connected. I've seen a 4 wire main residential panel on a site and the neutral and ground were separated. Are the connected somewhere else, such as meter base or transformer? Thanks
SER Cable in Conduit - Electrician Talk
2016年11月30日 · The SE Conductor is usually attached to the bottom of the floor joists. Real hard for that size to run it through the joists and also would required some pretty big holes. #4 SER is pretty small and I use 1 1/8" DareDevil spade bits to make holes when running it. 1" may work, but why fight it. It may be a code violation to bend the SER in the ...
Service entrance cable routed around a gutter - Electrician Talk
2011年8月1日 · The customer needs to have a new service installed. Due to a weird intersection of 2 rooflines, the current service entrance cable is routed around a section of gutter. The cable comes up from the meter socket to the bottom of the gutter, wraps around the gutter and is attached to the fascia of the one roofline until it ultimately meets the ...
Need Help With Service Entrance Cable Protection
2014年4月15日 · Need Help With Service Entrance Cable Protection. We have a standard 200amp overhead service. Comes into meter pan and from the meter pan we ran a 6' of 2"pvc into house to service entrance rated transfer switch. Out of switch we ran SER cable to panel. Inspector said we can't run that far in house as per code.
sleeve SE cable - Electrician Talk
2020年8月24日 · service-entrance conductors, other than underground service. entrance conductors, shall be protected against physical. damage as specified in 230.50 (B) (1) or (B) (2). (1) Service-Entrance Cables. Service-entrance cables, where subject to physical damage, shall be protected by any. of the following: (1) Rigid metal conduit (RMC)
Running SER through studs - Electrician Talk
2011年6月30日 · 379 posts · Joined 2010. #6 · Jun 30, 2011. I thought about running it in conduit, but SER cable is super cheap. 334.15 (C) states you can run nm cable that is 8/3 or larger on the bottom of joists. I'm wondering if I can run the cable perpendicular to the wall studs at a height that would protect it from any physical damage.
Can seu service cable be spliced? - Electrician Talk
2011年11月16日 · 230.46 Spliced Conductors. Service-entrance conductors. shall be permitted to be spliced or tapped in accordance. with 110.14, 300.5 (E), 300.13, and 300.15. 312.8 Switch and Overcurrent Device Enclosures with. Splices, Taps, and Feed-Through Conductors. The wiring.
Service Entrance Conductors - Electrician Talk
2008年5月22日 · A. Absolutetruthz Discussion starter. 195 posts · Joined 2008. #1 · May 22, 2008. Suggestions on what you guys use to splice Service Entrance Conductors to the Service Drop Conductors from the POCO. I have always used Butt splices.