home made tools and equipment... | The H.A.M.B. - The Jalopy …
2008年1月16日 · Since this is supposed to be about tools, here's a couple easy to make and not much $$. First one is a drill press outer stand gizmo. Works well if you have a bench mounted drill press. As you can see, if your vise isn't too far away you …
Home brew shop tools.... | The H.A.M.B. - The Jalopy Journal
2006年9月25日 · This one set up for tapping holes in a mag wheel so as to attach home-made hubcaps or the adapters for attaching 32 re-pro caps to a mag wheel. Couple of 1/4" aluminum wedge spacers for bandsaw use. They go on the back of the vise to space it out correctly when bandsawing small parts.
Shop Press Tooling | The H.A.M.B. - The Jalopy Journal
2012年1月3日 · Here is a press brake I made for a 20 ton press. The upper and lower dies are made from 4140 bar stock. The upper die is 1"x 3" and the lower is 1 1/2"x 1 1/2". It bends 1/4" flatstock for brackets with ease. I also made a die set to bend sheet metal with. Bcap55, Jan 3, 2012. SHARE POST #2.
Homemade Tools! | Page 2 | The H.A.M.B. - The Jalopy Journal
2004年1月1日 · Homemade slide hammer-no photo, 5/8 sucker rod with washer welded on end using cluster gear out of 55 Chev 3 spd, about 30" long welded piece of flat metal on end, bent little more than 90 degrees, hole in center.
home made tools and equipment... | Page 70 | The H.A.M.B.
2008年1月16日 · Got my inspiration here on the HAMB to build my own bullseye hammer and dolly, 1" conduit and some scrap metal found in the shop. I made it with a useable 36" throat, works great, when you are by yourself and trying to do the rear inner cab section on a 1946 Studebaker M series. This is the layout.
Tech Month~~Home made metal shaping tools | Page 3 | The …
2008年12月27日 · Here are some homemade tools for metalshaping. The E wheel is basically 3/16 steel welded in a box section with the lower anvil holder made from a semi driveshaft spline and yoke. A planishing hammer and other tools bolt to flanges welded to the sides to save space. Other tools include various hammers and a double ended shrinker/ planishing hammer.
home made tools and equipment... | Page 75 | The H.A.M.B.
2008年1月16日 · Cheap easy set of dividers, these ones are made out of 6mm stainless, hard to find a set that go big and are still useable for small stuff willo_96 , Feb 16, 2014 SHARE POST #2248
Home made tranny mounts... | The H.A.M.B. - The Jalopy Journal
2003年9月7日 · The trans was one of Ford's all-synchro three speeds. I got a 1/2" thick piece of aluminum about 4" wide and cut it long enough to span from the trans mount pad to the original rubber pad the 352's auto trans used. Drilled four holes to match the trans pad and the rubber mount, bolted it together and it worked fine for a long time.
Garage etiquette | Page 2 | The H.A.M.B. - The Jalopy Journal
2009年1月23日 · Home Forums > General Discussion > The Hokey Ass Message Board > Garage etiquette Discussion in ' The Hokey Ass Message Board ' started by 4t64rd , Jan 23, 2009 .
Shop Press Tooling | Page 4 | The H.A.M.B. - The Jalopy Journal
2012年1月27日 · This is the reason that the HAMB needs to be organized in sections like Shop Tools, Metalwork, Painting, etc. it's too hard to keep up with and find threads you are interested in. Yeah, I know about "subscribed".